ANALISIS PENGARUH JUMLAH LILITAN KOIL PADA PEMANAS MENGGUNAKAN TERMOKOPEL TIPE K DENGAN METODE INDUKSI

Authors

  • Lukman Aditya universitas krisnadwipayana
  • Eka Paksi satrianto universitas krisnadwipayana

Keywords:

Induction, Heater, Thermocouple

Abstract

Induction Heater is a technology that has long been made and used in industries that require metal materials in its production, usually in melting metal, a considerable amount of fuel is required because the melting point of the metal itself is quite high. The objective of this project is to create a simulated heating design that is simple and efficient using the ATmega328 microcontroller-based Induction Heater with Thermocouple type K as a temperature sensor which detects the temperature of the heated test material. The research objective is to find the results of time, heat, power and current from 3 variations of the Coil, which is Coil 1 with a thickness of 2,5 mm with 5 turns, Coil 2 with a thickness of 2,5 mm with 8 turns and coil 3 with a thickness of 3 mm with 5 turns. By heating the iron on 3 kinds of coils alternately from the initial temperature of the iron 33,25 oC to 100 oC, The results obtained from the calculation of Coil 1 produce heat of 1.501,875 Joule, 20,351 Watt of power and the current is 1,696 Ampere with its time result is 73,8 seconds, Coil 2 produces heat of 1.501,875 Joule, 23,234 Watts of power and the current is 1,936 Ampere with its time result is 64,4 seconds and Coil 3 produces heat of 1.501,875 Joule, 17,69 Watts of power and the current is 1,474 Ampere with its time result is 84,9 seconds.

References

Hakiki, M. Firman dan Dyah Riandari. (2018). “Rancang Bangun Sistem Induction

Heater Berbasis Mikrokontroller ATmega 328”. Universitas Negeri Surabaya : Surabaya.

Nababan, J. Wandes. (2015). “Rancang Bangun Pemanas Induksi Berdaya Rendah

dengan Menggunakan Solenoid Coil Berbasis Mikrokontroler ATmega 8535”.

Universitas Sumatera Utara : Medan. [3] Noviansyah, Ryan. (2012). “Pemanas Induksi (Induction Heating) Kapasitas 200 Watt”. Jurnal Ilmiah Universitas Gunadarma : Jakarta.

Rencono, A. Wati. (2000). “Desain dan Analisa Pemanas Induksi”. Universitas Katolik Soegijapranata : Semarang.

Wicaksono, A. (2015). “Pengaruh Beban pada Pengukuran Frekuensi Menggunakan Frekuensi Meter Digital Berbasis Mikrokontroler ATmega 8535”. Universitas Lampung : Bandar Lampung.

Lubis, W.T.S. (2017). “Rancang Bangun Inkubator Skala Laboratorium dengan Sistem Pemanas Induksi (Induction Heating) Berbasis Mikrokontroller Atmega 8535”. Universitas Lampung : Bandar Lampung.

Wahyudi, W. dan Santosa, T. H. A. (2008). “Pengaruh Penambahan Limbah Peternakan Pada Karakteristik Pembakaran Batubara”. Universitas Muhammadiyah Yogyakarta: Yogyakarta.

Zakaria, I. (2019). “Rancang Bangun Monitoring Keamanan Pintu Berbasis Arduino Menggunakan Radio Frequency Identification Dan Ip Camera Pada Ruang R6 Teknik Komputer”. Politeknik Negeri

Sriwijaya.

Arduino, S. (2016). “Mengenal Arduino Software (IDE)”. Diakses dari : https://www.sinauarduino.com/artikel/mengenal-arduino-software-ide/.

Kho,D.https://teknikelektronika.com/

Downloads

Published

2021-01-01

How to Cite

Lukman Aditya, & satrianto, E. P. (2021). ANALISIS PENGARUH JUMLAH LILITAN KOIL PADA PEMANAS MENGGUNAKAN TERMOKOPEL TIPE K DENGAN METODE INDUKSI. JURNAL ELEKTRO, 9(1), 28–37. Retrieved from https://journal.teknikunkris.ac.id/index.php/elektro/article/view/397